1998 Chevrolet Blazer - Consumer Discussions

Chevy Blazer Starting and Stalling Problems

• blazer stalls,spits and sputters

  Written by: babyontheway on Mar 15, 2013 3:54:58 PM

  HI, i have a 1998 chevrolet blazer 4.3L vortec V6. It was running fine at first. But it started the run very rough and shakes like crazy. the temperature gauge doesnt work even after installing a new temperature sensor. it does this everyday. sometimes on very short drives like at lunch it will drive fine on the way to the store and then drive like crap on the way back. the ... Read More

Chevrolet Blazer Heating and Air Conditioning

• Blazer heat

  Written by: deftinwulf on Jan 25, 2013 5:56:07 AM

  I have a 1998 Chevy Blazer ST-10. Recently, the fan decided it was only going to come on sometimes. It will come on when it's freezing cold outside. I've pulled fuses reset the computer by disconnecting the battery. The heat is on, but the fan will not kick on. It doesn't matter if it's on A/C, defrost, or heat. As well, when it does decide to come on, it will not ... Read More

Chevrolet Blazer GMC Jimmy Transmission Problems

• ?????help

  Written by: hilljay on Mar 23, 2011 8:08:07 AM

  how long is the trans dip stick in a 1998 chevy blazer 3.1 v6 4wd?

Chevy Blazer/GMC Jimmy

• The Blazer is too new.

  Written by: duntov on Jun 5, 2012 10:50:24 AM

  Whenever I see a 1998- or later S10/S15 Chevrolet / GMC with problems, I attribute that to the vehicle being too new. There has not been enough time for routine maintenance to correct all the original GM factory defects, If a S10/S15 can be maintained for 15 years before the owner or owners gives up and isends ther S10/S15 to the auto salvage yard, the original GM problems have been fixed ... Read More

Chevy Blazer Starting and Stalling Problems

• Never Again Will I GM

  Written by: s10junkowner on Jul 31, 2011 12:13:44 AM

  My 1988 s10 blazer did exactly this, Stall, cool down, and start back up. I tried everything, even the fuel pump. Still wasn't a fix, traded it in for another 1998 s10 blazer. Then about in 2004 I bought a 2002 ZR2 blazer and what takes place at 118K? $500.00 Fuel Pump! I had it replaced, and then only at 123k, This stalling issue arises. What do ya know?!?! I'm back ... Read More

Chevy Blazer GMC Jimmy Electrical Problems

• 4x4 not working

  Written by: nickyp1 on Jan 22, 2011 2:12:01 PM

  I have a 1998 chevy blazer all of a sudden my I cant get my 4x4 to engage, when I press the button 4 hi or 4 lo it lights up and I hear it clicking on. I have checked all the obvious fuses and I am getting voltage to the transfer case. At this point I am inclined to believe that there is a vacuum leak or disconnected hose somewhere ... Read More

Chevy Blazer Starting and Stalling Problems

• Stalling and power loss

  Written by: mdbowhunter on Jul 3, 2010 4:06:03 PM

  My 1998 Chevy Blazer has the habit of losing power and sometimes stalling while driving down the road. It is especially bad on hills but does do it on flat roads. It feels like it is loading up when the problem occurs. The engine has 128,000 on it and other than this issue it runs great. I am going to replace the fuel filter this evening but would like input from ... Read More

Chevrolet Blazer Heating and Air Conditioning

• Re: 1998 Chevrolet Blazer A/C [jlflemmons]

  Written by: Stever@Edmunds on Jun 28, 2010 9:48:13 AM

  I think the long term trend in cars is to lessen required maintenance as much as possible. So my feeling is that the engineers have improved the seals so that there is little risk of failure by not using the AC. Plus as you say, the AC comes on with the defrost. Then again, I suppose the manufacturers know that most people trade cars every 3 to 5 years and so ... Read More

• Re: 1998 Chevrolet Blazer A/C [steve_]

  Written by: jlflemmons on Jun 26, 2010 9:27:16 PM

  Steve, Running the compressor is an issue in any automotive system. It may not be mentioned as most folks will use there defroster/defogger during the winter, and thus run the compressor. It may not be as big an issue with R134A, but was definitely an R12 issue. Most systems now days use very, very little refrigerant. As an example, the S10 series Blazer/pickup uses less than 28oz of R134A!

• Re: 1998 Chevrolet Blazer A/C [dulinaa]

  Written by: Stever@Edmunds on Jun 25, 2010 11:29:45 PM

  I just downloaded a '98 Blazer owner's manual and I don't see anything in there from GM advising owners to run their AC at any time. It may have been an issue in the old days but I don't think it must be a problem now; otherwise the manual would say something. How To Find Your Car Owner's Manual Online

• Re: 1998 Chevrolet Blazer A/C [yourangellady]

  Written by: dulinaa on Jun 24, 2010 6:30:43 PM

  It will not harm your engine, BUT it can ruin you a/c by not running often. Its got the Use it or lose it policy. Your a/c system has lubrication oil mixed with and circulated by the refrigerant. The seals can dry up and crack, especially the front shaft seal on the a/c compressor, causing all the refrigerant to leak out.

• Re: 1998 Chevrolet Blazer A/C [yourangellady]

  Written by: jlflemmons on Jun 6, 2010 9:20:23 PM

  Has nothing to do with harming the engine. But you should run the ac or defroster at least once a month for a minute or so to keep the seals lubricated and the oil moving across the moving parts of the compressor.

• Re: 1998 Chevrolet Blazer A/C [yourangellady]

  Written by: Stever@Edmunds on Jun 6, 2010 8:02:48 PM

  In the old days, you were supposed to run the AC a few minutes a month all year round. As I recall, this was to keep the seals flexible (in the compressor I guess). Nowadays the AC will kick on when you run the defroster to dehumidify the air, so you shouldn't find anything in your manual about running the AC. And I don't see why never running the AC would ... Read More

• Re: 1998 Chevrolet Blazer A/C [tidester]

  Written by: dfhltd on Jun 6, 2010 6:38:04 PM

  Whoever told your girlfriend that is nuts. AC takes power from the engine just like the alternator, the power steering and the transmission and wheels. The AC is no different. That's what the engine is there for. Engines in cars made without AC do just fine. There is no way that not taking energy from the engine is going to hurt it.

• Re: 1998 Chevrolet Blazer A/C [yourangellady]

  Written by: tidester on Jun 6, 2010 4:14:01 PM

  I've never heard that before and don't know how it's possible but maybe someone else can offer some insight. tidester, host SUVs and Smart Shopper

• 1998 Chevrolet Blazer A/C

  Written by: yourangellady on Jun 6, 2010 2:01:52 PM

  My girlfriend owns a 1998 Chevrolet Blazer....She was told recently by a mechanic that if you don't use your A/C much, it could actually harm your engine. Is this true at all ? I would appreciate some help on this. Thanks so much.

Chevrolet Blazer GMC Jimmy Transmission Problems

• Need help with my 1998 Chevy Blazer

  Written by: memebear on Apr 18, 2010 10:55:30 AM

  My Blazer won't shift out of 2nd and acts like it's in neutral when it hits 25mph. Has reverse and the fluid, filter and pan was all just changed and clean. Was running fine till a few days ago. Can someone please help me. I love my truck and don't want to get rid of it. :(

• 1998 Chevrolet Trasmission problems

  Written by: heavnlycare on Mar 9, 2010 9:44:12 AM

  My Blazer shifts all the time. It shift wrong it will shift up instead of down and visa versa. Also the blinker sound (not the light) blinks when Im not pushing the break. Would all that me connected to the main computer or wires or all seperate problems. PLEASE HELP i'm sick and tired of haveing issues with this truck

Chevy Blazer Fuel Pump and Pressure Regulator Problems

• help

  Written by: bryonmax on Feb 6, 2010 5:04:44 AM

  i have a 1998 chevy blazer. my fuel pump went out. so i changed it and changed the pugs and wires. now it wont start so i use some starting fulid and it runs fine after that. been doing that for 3 months.now after a bad ice storm it dont wanna run it back fires thu the intake and when i give it gas while driving it wants to die and ... Read More

Chevrolet Blazer Noises and Sounds

• Re: 1998 Chevy Blazer 4X4 rumbly drivetrain [ripley09]

  Written by: freedom777 on Jan 14, 2010 10:42:51 PM

  I have the same problem, except the growling sound is coming from the front end. When I engage the 4WD, the sound goes away. Any luck figuring it out?

Chevy Blazer GMC Jimmy Electrical Problems

• Re: 1997 Chevy Blazer dome lights staying on..... [gfr214]

  Written by: koda5 on Jan 7, 2010 1:09:29 PM

  I have a 1998 Chevy Blazer and the Dome light is staying on. I changed the driver side door switch and it did not correct the problem. Has anyone solved the same problem?

Chevy Blazer GMC Jimmy Maintenance and Repair

• Re: Changing starter motor in 1998 chevy blazer 4.3 V6 [emydee23]

  Written by: lbeasley on Dec 19, 2009 6:22:00 AM

  emydee23, did you every get your blazer starter replaced? I'm in the process of replacing my 1998 blazer 4x4 starter now and cannot figure out an easy way to unbolt the wires connected to the solenoid. After a bunch of twisting and moving around, I finally got the starter to a point to where I can pull it out, but it wont come out unless the wires connected to the solenoid ... Read More

• Re: Changing starter motor in 1998 chevy blazer 4.3 V6 [emydee23]

  Written by: jlflemmons on Dec 7, 2009 6:54:40 PM

  Three plug wires each side. That fourth wire you see on the passenger side goes to the coil. If they are the original wires, they will be numbered. Otherwise you need to know that the cylinders are, front to back, drivers side 1,3,5, and passengers side 2,4,6. If you don't have a manual, look at the wires on the old cap before you take them off and make a diagram.

• Re: Changing starter motor in 1998 chevy blazer 4.3 V6 [emydee23]

  Written by: blazergirl96 on Dec 5, 2009 8:12:17 PM

  Yes there is a heat shield...access to the heat shield is through a hole cut in the inside of the wheel well, covered with a rubber flap. Wires I don't know about...replace them one at a time as not to mix them up.

• Changing starter motor in 1998 chevy blazer 4.3 V6

  Written by: emydee23 on Dec 5, 2009 4:42:39 PM

  I am trying to remove the stater motor in a 98 Chevy Blazer 4.3L vortec V6 4x4. It isn't a very easy part to get to, and I had major issues getting the bolt closest to the right side out, and am struggling with the second bolt. From what I have read and researched, it only takes the two main bolts to free up the unit for removal (aside from the ... Read More

Chevrolet Blazer Noises and Sounds

• Re: 1998 Chevy Blazer 4X4 rumbly drivetrain [ripley09]

  Written by: carmanghia on Nov 4, 2009 2:48:06 PM

  I hate to tell you this but it is probably your tires causing this noise. I had a similar experience when I purchased new Goodyear Wranglers. I learned that there are many different tire designs all under the Wrangler name. The tire store had put on an All-Terrain design on. Anyhow, I didn't even make it home on these new tires as the noise was so objectionable. I had the tire ... Read More

• 1998 Chevy Blazer 4X4 rumbly drivetrain

  Written by: ripley09 on Nov 4, 2009 9:21:52 AM

  I have a 1998 Chevy Blazer 4X4 and when i hit 45-55 mph i get a horrible growl/rumble (sound and feels like you hit the caution rumble strip on the road) from somewhere in the drivetrain. i have replaced the rear end barrings, took out the front drive shaft, replace the 4x4 drive vacuum pod. The problem didn't start till i put the new tire on it (goodyear ranglers). The issue ... Read More

Chevrolet Blazer Brake Problems

• new preformed brake lines

  Written by: duntov on Sep 20, 2009 12:21:08 PM

  Having a autro repair shop bend straight tubing to fit your 1998 Blazer will be labor intensive and at $70 to $90 per hour, it would be serious money. The cost of the parts is nothing compared to the labor cost which is usually the case at auto repair shops. Except some of the electronic components that only take a few minutes to replace. It would be best to purchase preformed ... Read More

Chevrolet Blazer Heating and Air Conditioning

• Stealership prices

  Written by: duntov on Apr 23, 2009 8:14:09 AM

  Never go to a dealership to get service or repairs on a vehicle that is out of warranty. Dealerships have their hands full with warranty work on the new cars they sell and they discourage work on cars that are out of warranty. The dealership will give a car owner that has a car out of warranty a "courtesy bid" which will be far above and beyond the average independent auto ... Read More

94 Chevy Blazer 4x4 light flashes

• 1998 chevy s10 blazer clicking under steering column

  Written by: waterggoo on Apr 19, 2009 11:48:11 PM

  When I apply the brakes and sometimes while driving I hear a repeatedly clicking under the steering column. sounds like a flasher

Chevy Blazer GMC Jimmy Electrical Problems

• electrical problems

  Written by: ccbecke on Nov 24, 2008 7:43:40 PM

  Hi, I have a 1998 Chevy Blazer. First the windshield wipers were acting funny, they sometimes wont stop after I turn them on. Then the blinker on the right side keeps acting like it is on intermittently. Then the dome lights quit working and now the light that lights up where you push the button to put it into 4WD or 2WD is not working, and so it is stuck in ... Read More

• Re: 1998 Chevy Blazer: turn signal problems [repairdog]

  Written by: cardoc50 on Feb 27, 2009 1:54:28 PM

  General Motors issued a recall on the windshield wiper problem. It takes them about 20 minutes to do the recall. Solder on the printed circut board would crack thus leaving them inoperable. I know this because it happened to me. There was no problem scheduling the vehicle for the recall because they are able to do it very quik.

• Wiper only works on High

  Written by: jthompson5 on Jan 1, 2009 4:51:09 PM

  Would someone help me in understanding how my wipers work only on High? Everything else on the multifunction switch works... I already plugged in a new wiper motor (which includes circuit board). Do I need a new multifunction switch and if so, are they somewhat easy to install? I have a 1998 Chevy blazer. Thanks for the help..

Chevrolet Blazer GMC Jimmy Transmission Problems

• can you help me out?

  Written by: bmcwall on Nov 17, 2008 5:44:42 PM

  I have a 1998 Chevy Blazer (LS?), 4 door, 4x4, automatic, rear wheel drive i read this page of posts, and my car sounds like a combo of everything. I should start from the begining. i recieved my car as a gift from my father, when he handed it over everything was all right with it i think. he got a 30,000 mile (tuneup?) like thing. Last year I was driving ... Read More

Chevy Blazer GMC Jimmy Maintenance and Repair

• parking brake release broken

  Written by: brian352chevy on Oct 5, 2008 4:58:17 PM

  my parking brake release is broken on my 1998 4 door chevy blazer.the parking break is stuck on any idea on how to take it off with out the release handle

• Re: Heater won't work in our 1998 chevy blazer [pribylcrew]

  Written by: sealteam8 on Oct 4, 2008 11:01:10 PM

  The 02 sensor has nothing to do with the heater. Either the thermostat doesnt work or it could be low on antifreeze. As well as the heater core might be cracked. ANy smell of antifreeze in the cab of the truck? If not check the thermostat...

Chevrolet Blazer Engine and Performance Problems

• Re: 1998 Chevy blazer looses power and stalls [bigt442]

  Written by: sealteam8 on Oct 4, 2008 10:54:31 PM

  The water leak shouldnt cause a vacum leak although it may! But the code lean on bank one tells me that the o2 sensor is bad, also check to make sure the firing order is right as well! The code says the o2 sensor in bank one is bad which means the sensor befor the cat. try replacing that one. there should only be 2 of them on that model

Chevrolet Blazer GMC Jimmy Transmission Problems

• 1998 Chevy Blazer tranny problem

  Written by: mkc716 on Sep 3, 2008 11:40:34 AM

  About 2 months ago, I had a spring replaced in my tranny. The problem was it was shifting hard between 1st and 2nd. That seemed to fix it. However, Just today it started doing it again. I was wondering if I should take it back to the shop that fixed it and ask them to replace the control valve body this time ??

Chevrolet Blazer Engine and Performance Problems

• 1998 Chevy blazer stalls.

  Written by: bigt442 on Jun 1, 2008 10:58:44 AM

  I have a 1998 chevy blazer that I have now replaced the fuel pump and filter. I have also replaced the intake gaskets, mas air flow sensor and have tested all other sensors. All of them have check fine.The only other sensors to be check are the cam and crank. So now here is the problem, It will start but when you go to give it the gas it will stall ... Read More

• Re: 1998 Chevy blazer looses power and stalls [bigt442]

  Written by: jlflemmons on May 22, 2008 8:26:03 PM

  Leaking intake manifold gasket, fairly common on these engines with high mileage.

• 1998 Chevy blazer looses power and stalls

  Written by: bigt442 on May 22, 2008 12:26:32 PM

  I have a 1998 blazer that has had the fuel pump and filter replaced. It still seems to lack power and sometimes backfire or burp back thru the throttle body. fuel pressure seems to be with in tollerance, but have noticed a water leak at the back of the intake. So with that leak could a vacume leak cause it to run like this also. I have had a code that ... Read More

Chevrolet Blazer GMC Jimmy Transmission Problems

• Trans shifts hard between first and second

  Written by: jaredw on Feb 4, 2008 1:54:14 PM

  I have a 1998 chevy blazer with 130000 miles, a while back (15000 miles ago)I changed my trans pan fluid and filter due to the same problem, and this fixed the problem until now, I was reading the earlier entries, do you think I should replace my converter fluid, will this help the problem, or should I replace the Tcc solenoid. The problem occurs between 25-35 mph when it shifts into ... Read More

Chevrolet Blazer Heating and Air Conditioning

• 1998 S-10 blazer Msg 59 update HEAT AGAIN

  Written by: woodboatchick on Jan 13, 2008 9:58:59 AM

  Ok, so we spent some quality time with the '98. First I went to the local Chevy dealer where the parts mgr was kind enough to give me copies of the exploded diagrams for this heater box flapper/valve/door system. It turns out that the issue for this problem centers on the 'valve' that is on the left side(driver's) side of the heater box. Due to the number of times that this ... Read More

Chevrolet Blazer Engine and Performance Problems

• 98 Blazer steady speed it Misfires

  Written by: doc_john_13 on Apr 30, 2006 3:17:35 PM

  Hello, I have a 1998 Chevy Blazer. The Idle is fine, the acceleration is fine. But when you get it up to a steady speed it Misfires. I have changed spark plugs, and plug wires. Replaced the fuel filter. Ran injector cleaner time and time again. I don't know what else to do. Can you PLEASE help me? thank's John

Chevy Blazer GMC Jimmy Electrical Problems

• Re: Quick off topic one time question [roregan]

  Written by: jlflemmons on Aug 1, 2007 9:07:57 PM

  Appreciate your reply. What I have found out is that the remote changed between '01 and '02. The part number I am finding for '98 through '01 is 15732805. Make Model Year(s) Application Chevrolet Astro 2000 RPO AU0, Each 2001 RPO AU0, ID #15732805, Each Chevrolet Blazer 1998-2001 Each, 1st Design GMC Envoy 1998-2000 Each GMC Jimmy 1998-2001 Each, 1st Design GMC Safari 2000 RPO AU0, Each 2001 RPO AU0, ID ... Read More

Chevy Blazer GMC Jimmy Maintenance and Repair

• Heater won't work in our 1998 chevy blazer

  Written by: pribylcrew on Jan 14, 2007 5:59:10 PM

  The heater won't work, I know that the c02 sensor has to be replaced. The heater didn't work about a week ago, we just had a CD player put in and now the heater won't work?! I'm hoping someone knows something. Any suggestions?

Chevy Blazer GMC Jimmy Electrical Problems

• Re: 1998 Chevy Blazer: turn signal problems [david565]

  Written by: repairdog on Oct 22, 2006 4:53:39 AM

  Normally just the card goes bad and never had to do a motor. As you will see the torx screws may be hard to reach without a bit and a 1/4" drive and add a thin bead of silicon sealer to the cover edge to seal the moisture out and gently snug the screws so you don't flex the card,

• Re: 1998 Chevy Blazer: turn signal problems [repairdog]

  Written by: david565 on Oct 21, 2006 4:50:20 PM

  I tapped the motor and and the wipers go on and off, so thats definately the problem. I'll try to clean the card, but if that doesn't work could I replace just the card (looks like they cost about $20 - they call it a wiper motor pulse board), or do you recommend replacing the entire motor? Thanks for all your help!

• Re: 1998 Chevy Blazer: turn signal problems [david565]

  Written by: repairdog on Oct 21, 2006 2:43:03 PM

  Yep, that's the circuit card in the wiper motor (drivers side under hood)- it can be burned traces or a simple remove, clean the grease off and install again not over tightening the 3 cover torx screws that can distort the card. Common problem and many stores carry the card at approx $50. if required.

• Re: 1998 Chevy Blazer: turn signal problems [e5husmc]

  Written by: david565 on Oct 21, 2006 1:57:59 PM

  Well I got a new switch and finally got it put in. Everything works except I'm still having problems with the windshield wipers. The pulse works, and high speed wipe, and the spray wipe work, but regular speed wipe and delay wipe still don't work. Any suggestions?

• Re: 1998 Chevy Blazer: turn signal problems [david565]

  Written by: e5husmc on Oct 2, 2006 5:12:36 PM

  Taking the switch out isn't hard as long as are careful, taking the switch apart isn't too bad but can be fun to put back together. Look at this way, you can try to fix the switch first, worst-case you will need to buy a new switch.

• Re: 1998 Chevy Blazer: turn signal problems [e5husmc]

  Written by: david565 on Sep 26, 2006 3:20:45 PM

  I have a 98 Blazer with the same problem. It started with the clicking behind the glove box, then the cruise control stopped working, and now the windshield wiper works only when it wants to. Does it sound like cleaning out the di-electric grease and replacing it will fix these problems, or do you think I need to get a new switch? Is replacing the grease complicated?

• Re: 1998 Chevy Blazer: turn signal problems [pherpin]

  Written by: e5husmc on Sep 19, 2006 10:27:22 AM

  I have a 98 Jimmy had the same problem. The problem is in the turn signal switch, small particles of metal (from the contact points) get mixed with the di-electric grease. You can either buy a new switch or remove the old switch and take it apart, clean-out the old grease then apply new di-electric grease. According to the repair manuals you have to pull the stearing wheel but I managed ... Read More

• Re: 1998 Chevy Blazer: turn signal problems [pherpin]

  Written by: repairdog on Sep 6, 2006 4:02:09 AM

  Sorry they have so search on multifunction switch - its in the steering column and may be shorting so you hear the flasher relay behind the glove box. Try replacing the relay thats clicking first - left side of glove box put your hand in there and gently bend the corner of the glove box down and it will drop open to access behind it.

• 1998 Chevy Blazer: turn signal problems

  Written by: pherpin on Sep 5, 2006 4:10:03 PM

  Hopefully someone will be able to help with this problem. Recently my my 98 blazer started having problems. Whenever I am driving, I can hear the turn signal clicking, even though the turn signal is not on. Has anyone else had this problem?

Chevrolet Blazer Warning Lights and Gauges

• Re: 1998 Chevy Blazer - Manufacturer Controlled Transmission Code P1970 [theugamom]

  Written by: repairdog on Jul 29, 2006 3:50:50 AM

  Believe you meant P1870. TSB # 01-07-30-023A Harsh 1-2 Upshift, SES, MIL, or CEL Illuminated, DTC P1870 Set (Replace Valve Body) When the conditions for setting DTC P1870 are met (first trip), the PCM commands maximum line pressure and harsh 1-2 shifts are the result. This may result in a harsh 1-2 shift with no history code if the conditions for setting the DTC required for the second trip are not ... Read More

• 1998 Chevy Blazer - Manufacturer Controlled Transmission Code P1970

  Written by: theugamom on Jul 28, 2006 7:03:44 PM

  My check engine light just came on while traveling from Miami to Savannah, GA. I had the code read at Autozone and they said it was P1970 - manufacturer controlled transmission code and to see a dealer. Is there a way to fix this myself or must I take it to a dealer. Transmission is slipping a little but not bad - yet!

Chevy Blazer GMC Jimmy Maintenance and Repair

• check engine light

  Written by: martymac24 on Jul 22, 2006 9:25:53 PM

  i have 1998 chevy blazer,how can i get the check engine light to go out without fixing anything?

• Re: 1998 Chevy Blazer Cruise Control stopped working [doc_john_13]

  Written by: repairdog on Jun 16, 2006 2:25:46 AM

  Switch mounted above the brake pedal that shuts cruise off when you apply the brakes may be bad and they are cheap but a pain to bend yourself to reach up in there - may have to take the plastic piece off to reach it but only 3-5 small screws hold it up there - somewhere around 6-8 mm heads.

• 1998 Chevy Blazer Cruise Control stopped working

  Written by: doc_john_13 on Jun 15, 2006 5:29:14 PM

  When I set the Cruise Control nothing happens. I checked the fuse in the fuse box. I put the radio to AM, and I can hear it click on and off. I do not hear anything when I push the set button. Don't know what to check next, or what to do. Help Thank's John

Chevy Blazer/GMC Jimmy

• GM Customer Service Dept.

  Written by: bsc338 on Dec 26, 2005 2:57:47 PM

  When reverse and overdrive both failed same day in my 1998 Blazer, dealer said repaiing parts would cost 3300 and putting in a GM Remanufactured trans would cost 3700. Blazer had 59,000 miles and never towed or hauled anything heavy. I called GM Cust. Service 1-800 number and after much hem and haw they said if I did have 3700.00 repair job done, they would pay 50% of cost, in form ... Read More

Chevy Blazer GMC Jimmy Maintenance and Repair

• 98 Blazer steady speed it Misfires

  Written by: doc_john_13 on May 1, 2006 3:04:02 AM

  Hello, I have a 1998 Chevy Blazer. The Idle is fine, the acceleration is fine. But when you get it up to a steady speed it Misfires. I have changed spark plugs, and plug wires. Replaced the fuel filter. Ran injector cleaner time and time again. I don't know what else to do. Can you PLEASE help me? thank's John

• Re: 4wd noise [repairdog]

  Written by: danmac2d on Apr 6, 2006 8:33:14 PM

  i have a 1998 chevy blazer and when i take off it sounds like a splashing in the engine i have no leaks form the heating coil any sugestions

• Re: 1999 Chevrolet Blazer Clicking Turn Signal Noise [kevin53]

  Written by: ebs57 on Sep 22, 2005 10:23:35 AM

  Hey Kevin, My 1998 Chevy Blazer has been doing this for the last 5 days. Man, I have been to several auto-electrical shops and have replaced the flasher twice. Your explanation has been the best and makes the most sense of all. Just when I had reached the end of my rope. Thanks for the knot. I'll get back with you to let you know how it worked out. Peace out. ... Read More

• Re: 1999 Chevrolet Blazer Clicking Turn Signal Noise [smush29]

  Written by: dec4br on Jul 15, 2005 12:44:28 AM

  I have a 1998 Jimmy that has the same problem with the noisy signal. I think the noise is coming from a flasher switch behind the Glove Box on Passenger side. How do you get to it or do you know of a site with an illustration for location and part? Thanks.dec

Chevy Blazer/GMC Jimmy

• FIRE PLEASE HELP!!!

  Written by: tarah on May 22, 2005 11:44:11 AM

  Hi all, Last week as I was driving my 1998 Chevy Blazer, I noticed a strange smell that I assumed was coming from outside. However, as I continued down the freeway, I noticed that smoke was coming from the car. At first I could not locate its origin, but when I looked down, it was coming from the driver's seat!! I immediately pulled over, and looked under the seat, from the ... Read More

Chevy Blazer GMC Jimmy Maintenance and Repair

• Re: 1999 Chevrolet Blazer Clicking Turn Signal Noise [smush29]

  Written by: kevin53 on May 12, 2005 9:43:04 AM

  I have a 1998 GMC Jimmy that had the same problem. I searched and searched for the answer, and found it late one night. The fix is relatively simple. When the turn signal is turned on little metal shavings rub off. These shavings get into the lubricant around the connectors and end up bridging the gap between circuits. So in essence, the turn signal switch is partially connected, which is why ... Read More

• Re: 1999 Chevrolet Blazer Clicking Turn Signal Noise [smush29]

  Written by: kman0199 on May 4, 2005 11:25:03 AM

  I am having the same problem with my 1998 Blazer it must be common

• Follow-up

  Written by: sockpuppet1969 on Aug 25, 2004 1:42:57 PM

  Re: mssg 932 (the last message) I got the truck back from the mechanic today. He replaced the "combination switch" which controls the flasher module for the directionals. This stopped the intermittent blinker noise. Cost: $300 parts and labor. (Value of not having to hear the blinker noise ALL the time while driving: priceless!) He cleared the airbag code and we will wait to see if the idiot light comes back ... Read More

• RE:Advice on fixing recliner handle

  Written by: houcwb on Aug 10, 2003 9:41:16 AM

  Previously posted: Hi. I just bought a 1998 Blazer 2wd 2dr. Both seat reclining handles are broken. The seats are in a pretty good position but, if it doesn't break the bank, I'd like to get them fixed. I did a search and found some who had had the same problem but I found no info on cost of repair. Would needle nose pliers or vise grips let me adjust the ... Read More

• recall info

  Written by: spoom on Aug 9, 2003 2:09:22 PM

  a while back in this thread there was discussion about driver door fires from the lock/window/mirror assy. I see that it finally went to the recall stage so if you haven't had the update here is the info: General Motors Corporation Models: Chevrolet Blazer Year: 1997 GMC Jimmy Year: 1997 Chevrolet Astro Year: 1998 GMC Safari Year: 1998 Chevrolet C/K Series Year: 1998 GMC C/K Series Year: 1998 Chevrolet Suburban Year: ... Read More

• 1998 Blazer problems!

  Written by: vf99 on Jun 25, 2003 4:26:23 PM

  I have a 98 Blazer and it's just been one problem after another this year. I had to replace the fuel pump (the Blazer died on me at a stoplight), also replaced the thermostat this year and now the biggie - replaced the engine. It had a cracked engine block, there was exhaust blowing into the radiator. So, I'll be looking into a new car soon! Oh, and last year I ... Read More

• 1998 Chevy Blazer LT 4WD problem

  Written by: rjgold on May 20, 2002 8:48:16 PM

  The darn truck pulls to the right no matter what I do! I just put new tires on it a couple of weeks ago and had the front-end aligned last week at the local Chev dealership. I took it on a 400+ mile round-trip this weekend and it's still pulling to the right. I live in the NW and a lot of roads are sloped to the right to allow for ... Read More

• 98 Blazer Squeak/Squelch

  Written by: my98blazer on Sep 22, 2001 1:09:19 PM

  Hello all, I've checked the board and can find no reference to this problem. Maybe someone can help. I purchased a used 1998 Chevy Blazer 4X4 4 dr.w/46k miles. Truck works great except for one thing. After a 250 mile trip with the cruise on I notice that the truck suspension seemed to be squeaking when I went over bumps or pot holes, or even turned the steering wheel. I immediately ... Read More

• 1998 Chevy Blazer LT - Size of Gas Tank??

  Written by: ba_ba_booee on Feb 17, 2001 5:03:39 AM

  Accordingto the original window sticker on my 98 Blazer it is supposed to have an 18 gallon tank but I have never put more than 16 gallons in it and that includes topping off the tank. I ran out of gas once and it only took about 15.5 gallons to fill it completely. I have occassionally driven it down to extremely low levels and still haven't been able to put more ... Read More

Chevy Blazer/GMC Jimmy

• Bad Service at Horizon Chevrolet in Illinois

  Written by: michaelm11 on Mar 9, 2001 1:11:49 PM

  I took my 1998 Blazer LT into the dealership to get a routine oil change, replace the master control window unit switch (pre-ordered) and to check the security light that periodically came on. I dropped my car off at 7:00AM and this is where the adventure begins. At 1:30PM I got a call from the service manager and he told me that the ignition switch was bad. It was causing the ... Read More